Just about everyone has got his or her own idea with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bath tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move rapidly; if you need to open a wall to get rid of the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and also set in the new one. See to it you have actually qualified yourself for the task and also are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed project, it is better to think about using one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This write-up will help you set up a new tub in your washroom if you have actually already bought a new tub as well as do not need to alter the plan of your previous water pipelines.
Your devices and material checklist ought to make up the following:
Getting ready for the Setup
Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both taps utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome due to the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply as well as inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the bathtub and also check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has actually been utilized at the very least once as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location between the tap and also the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with dampness and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that excerpt was smart. Liked our write-up? Please share it. Let others check it out. Bless you for your time. Kindly come by our site back soon.
Estimating